Sliding Wear Study of Flame Sprayed Co-Base Powder Coatings
DOI:
https://doi.org/10.6000/2369-3355.2014.01.02.5Keywords:
Co-base, Flame spraying, Microstructure, Hardness, Adhesive wear.Abstract
Commercially available Co-base powder was modified with the addition of 10 wt. percentage WC which was further modified with 5 and 10 wt. percentage CrC addition in order to obtain three coatings namely Co+10 wt. percentage WC, Co+10 wt. percentage WC+5 wt. percentage CrC and Co+10 wt. percentage WC+10 wt. percentage CrC. The coatings were deposited by flame spraying process. The microstructure of these coatings mainly showed eutectic containing Co with almost same amount in three coatings. Other phases such as W dominated and Cr dominated carbides were also observed. The 10 wt. percentage CrC coating showed the highest Vickers hardness and lowest wear rate. The coefficient of friction was also observed low in the 10 wt. percentage CrC coating as compared with other coatings.References
Ghosh PK, Dwivedi DK, Mishra PS. Studies on oxidation and wear resistance of hard surface produced by gas thermal spraying of modified nickel base eutectic alloy powder. Indian Weld J 2001; 34: 35-41.
Miguel JM, Guilemany JM, Vizcaino S. Tribological study of NiCrBSi coating obtained by different processes. Tribol Int 2003; 36: 181-7. http://dx.doi.org/10.1016/S0301-679X(02)00144-5
Kim HJ, Kim YJ. Wear and corrosion resistance of PTA weld surfaced Ni and Co based alloy layers. Surf Eng 1999; 15: 495. http://dx.doi.org/10.1179/026708499101516911
Fritsch A, Gadow R, Killinger A. Development of Highly Wear Resistant Coatings for Deflector Blades in Paper Industry in Thermal Spray: Surface Engineering via Applied Research (Proceedings of ITSC 2000), C.C. Berndt, ed., ASM International, Materials Park, OH, 2000, pp. 1051-55.
Strock E, Ruggiero P, Reynolds D. The Effect of Off-Angle Spraying on the Structure and Properties of HVOF WC/CoCr Coatings in Thermal Spray 2001: New Surfaces for a New Millennium (Proceedings of ITSC 2001), C.C. Berndt, K.A. Khor, and E.F. Lugscheider, ed., ASM International, Materials Park, OH, 2001, pp. 671-76
Nascimento MN, Souza RC, Miguel IM, Pigatin WL, Voorwald HJC. Effects of Tungsten Carbide Thermal Spray Coating by HP/ HVOF and Hard Chromium Electroplating on AISI 4340 High Strength Steel. Surf Coat Technol 2001; 138: 113-24. http://dx.doi.org/10.1016/S0257-8972(00)01148-8
Khedkar J, Khanna AS, Gupta KM. Tribological Behavior of Plasma and Laser Coated Steels. Wear 1997; 205: 220-7. http://dx.doi.org/10.1016/S0043-1648(96)07291-2
Chandak A, Sivakumar R, Balasubramanian G. Tribological Solutions for Engineering Industries by HVOF—Topgun Spraying in Thermal Spray: Meeting the Challenges of the 21st Century, Proceedings of the 15th International Thermal Spray Conference, C. Coddet, ed., ASM International, Materials Park, OH, 1998. pp. 531-53.
Keshavan MK, Kembalyan KT. Wear Characterisation and Practical Applications of Thermal Spray Coatings in Drilling Applications” in Proceedings of the 1993 National Thermal Spray Conference, C.C. Berndt and S. Sampath, ed, ASM International, Materials Park, OH, 1993, pp. 635-41.
Peters JA, Ghasripoor F. Sliding Wear Behavior of Carbide Coatings in Advances in Thermal Spray Science and Technology: Proceedings of the 8th National Thermal Spray Conference, C.C. Berndt and S. Sampath, ed., ASM International, Materials Park, OH, 1995, pp. 387- 92.
Jia K, Fisher TE, Gallois B. Microstructure, Hardness and Toughness of Nanostructured and Conventional WC-Co Composites. Nanostruct Mater 1998; 10: 875-91. http://dx.doi.org/10.1016/S0965-9773(98)00123-8
Wong TT, Liang GY, He BL, Woo CH. Wear resistance of laser-clad Ni-Cr-B-Si alloy on aluminium. J Mater Process Technol 2000; 100: 142-6. http://dx.doi.org/10.1016/S0924-0136(99)00463-X
Rodriguez J, Martín A, Fernández R, Fernández JE. An experimental study of the wear performance of NiCrBSi thermal spray coatings. Wear 2003; 255: 950-5. http://dx.doi.org/10.1016/S0043-1648(03)00162-5
Sundararajan T, Kuroda S, Abe F, Sodeoka S. High temperature corrosion of nanoceria coated 9Cr-1Mo ferritic steel in air and steam. Surf Coat Technol 2006; 201: 2124-30. http://dx.doi.org/10.1016/j.surfcoat.2006.02.007
Skulev H, Malinov S, Sha W, Basheer PAM. Microstructural and mechanical properties of nickel-base plasma sprayed coatings on steel and cast iron substrates. Surf Coat Technol 2005; 197: 177-84. http://dx.doi.org/10.1016/j.surfcoat.2005.01.039
Skulev H, Malinov S, Basheer PAM, Sha W. Modifications of phases, microstructure and hardness of Ni-based alloy plasma coatings due to thermal treatment. Surf Coat Technol 2004; 185: 18. http://dx.doi.org/10.1016/j.surfcoat.2003.12.012
Torrance AA. The effect of grit size and asperity blunting on abrasive wear. Wear 2002; 253: 813-9. http://dx.doi.org/10.1016/S0043-1648(02)00103-5
Moore MA. A review of two-body abrasive. Wear 1974; 27: 1-17. http://dx.doi.org/10.1016/0043-1648(74)90080-5
Cachon L, Sudreau F, Denape J, Lelait L. Tribological qualification of cobalt-free coatings for pressurized water reactor primary-circuit gate valve applications. Surf Coat Technol 1996; 85: 163-9. http://dx.doi.org/10.1016/0257-8972(95)02672-X
Mateos J, Cuetos JM, Vijande R, Fernandez E. Tribological properties of plasma sprayed and laser remelted 75/25 Cr3C2/NiCr coatings. Tribol Int 2001; 34: 345-51. http://dx.doi.org/10.1016/S0301-679X(01)00023-8
Kayuk V, Panasyuk A, Grigor’ev O. Reactions of Cr3C2- TiN system materials with nickel-chromium alloys. Powder Metall Met Ceram 2006; 45: 365-70. http://dx.doi.org/10.1007/s11106-006-0091-0
Sundararajan T, Kuroda S, Abe F. Effect of thermal spray on the microstructure and adhesive strength of high-velocity oxyfuel- sprayed Ni-Cr coatings on 9Cr-1Mo Steel. Metall Mater Trans A 2004; 35: 3187-99. http://dx.doi.org/10.1007/s11661-004-0063-2
Dent AH, Horlock AJ, McCartney DG, Harris SJ. Microstructural characterisation of a Ni-Cr-B-C based alloy coating produced by high velocity oxy-fuel thermal spraying. Surf Coat Technol 2001; 139: 244- 50. http://dx.doi.org/10.1016/S0257-8972(01)00996-3
Bahrololoom ME, Hoveidaei A. Influence of post-heat treatment and complexing agents on hardness of Ni-Cr alloy coatings. Surf Eng 1999; 15: 502-4. http://dx.doi.org/10.1179/026708499101516830
Dawei Z, Li T, Lei TC. Laser cladding of Ni-Cr3C2/ (Ni+Cr) composite coating. Surf Coat Technol 1998; 110: 81-5. http://dx.doi.org/10.1016/S0257-8972(98)00675-6
Wang TG, Zhao SS, Hua WG, Gong J, Sun C. Design of separation device used in detonation gun spraying system and its effects on the performance of WC-Co coatings. Surf Coat Technol 2009; 203: 1637- 44. http://dx.doi.org/10.1016/j.surfcoat.2008.12.012
Sarjas H, Goljandin D, Kulu P, Mikli V, Surenkov A, Vuoristo P. Wear resistant thermal sprayed composite coatings based on iron selffluxing alloy and recycled cermet powders. Mater Sci 2012; 18: 34-9.
Shetty HR, Kosel TH, Fiore NF. A study of abrasive wear mechanisms using diamond and alumina scratch tests. Wear 1982; 80: 347-76. http://dx.doi.org/10.1016/0043-1648(82)90262-9
Corchia M, Delogu P, Nenci F. Microstructural aspects of wearresistant stellite and colmonoy coatings by laser processing. Wear 1987; 119: 137-52. http://dx.doi.org/10.1016/0043-1648(87)90105-0
Otterloo JL, De Mol Van, Hossont JTHM. Microstructure and abrasive wear of cobalt-based laser coatings. Scripta Materialia 1997; 36: 239- 45. http://dx.doi.org/10.1016/S1359-6462(96)00346-6
Otterloo JL, De Mol Van, Hossont JTHM. Microstructural features and mechanical properties of a cobalt-based laser coating. Acta Materialia 1997; 45: 1225-36. http://dx.doi.org/10.1016/S1359-6454(96)00250-9
Lebaili S, Durand-Charee M, Hamar-Thibault S. The metallurgical structure of as-solidified Ni-Cr-B-Si-C hardfacing alloys. J Mater Sci 1988; 23: 3603-11. http://dx.doi.org/10.1007/BF00540502
Mohanty M, Smith RW. Sliding wear behavior of thermally sprayed 75/25Cr3C2/NiCr wear-resistant coatings. Wear 1996; 198: 251-66. http://dx.doi.org/10.1016/0043-1648(96)06983-9
Suh NP. Tribophysics, Prentice-Hall, New Jersey, 1986, pp. 63-90.
Mart?n A, Rodr?guez J, Fernández JE, Vijande R. Sliding wear behavior of plasma sprayed WC-NiCrBSi coatings at different temperatures. Wear 2001; 251: 1017-22. http://dx.doi.org/10.1016/S0043-1648(01)00703-7
Downloads
Published
How to Cite
Issue
Section
License
Policy for Journals/Articles with Open Access
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are permitted and encouraged to post links to their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work
Policy for Journals / Manuscript with Paid Access
Authors who publish with this journal agree to the following terms:
- Publisher retain copyright .
- Authors are permitted and encouraged to post links to their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work .