Structural, Morphological, Optical Properties and Modelling of Ag Doped CuO/ZnO/AZO Solar Cell
DOI:
https://doi.org/10.6000/2369-3355.2022.09.04Keywords:
Ag doping, CuO thin film, SCAPS-1D simulation, solar cellAbstract
Copper (II) oxide (CuO) has attained significant attention from researchers because of its unique chemical and physical properties. Ag-doped CuO thin films have been produced on the soda glass substrate (SLG) by spin coating technique at different doping ratios. Structural, morphological, and optical properties of thin films produced depending on altered silver ratios have been examined through X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM), and UV-vis absorption spectroscopy, respectively. Band gaps of prepared undoped and 1% Ag-doped CuO thin films have been measured as 1.90eV and 1.63eV, respectively. Ag/undoped CuO and Ag-doped CuO/ZnO/AZO solar cells have been modelled, and their photovoltaic parameters have also been calculated using the SCAPS-1D simulation program. This work aims to investigate the photovoltaic parameters that would improve the efficiency of a solar cell. The effect of Ag atoms on the efficiency of CuO solar cells has been investigated depending on the acceptor density (Na), the interface defect density (Nt), and the operating temperature. Ag-doped CuO solar cells have shown the highest efficiency for Nt=1010 cm-3 and Na=6, 5x1016 cm-3 values. It has been well observed that as the operating temperature increases, the solar cells’ power conversion efficiency decreases. The highest charge generation rates in the undoped and Ag-doped solar cells have been determined as 1.49×1022 1/cm3.s and 1.51×1025 1/cm3.s, respectively. All the results, either theoretical or experimental, have been presented in this work and have been compared for a conclusion that has been made in detail.
References
Deng H, Li H-r, Wang F, Yuan C-x, Liu S, Wang P, et al. A high sensitive and low detection limit of formaldehyde gas sensor based on hierarchical flower-like CuO nanostructure fabricated by sol-gel method. J Mater Sci Mater Electron 2016; 27(7): 6766-72. https://doi.org/10.1007/s10854-016-4626-y
Sanal K, Vikas L, Jayaraj M. Room temperature deposited transparent p-channel CuO thin film transistors. Appl Surf Sci 2014; 297: 153-7. https://doi.org/10.1016/j.apsusc.2014.01.109
Chaudhary YS, Agrawal A, Shrivastav R, Satsangi VR, Dass S. A study on the photo-electrochemical properties of copper oxide thin films. Int J Hydrog Energy 2004; 29(2): 131-4. https://doi.org/10.1016/S0360-3199(03)00109-5
Bhaumik A, Haque A, Karnati P, Taufique M, Patel R, Ghosh K. Copper oxide based nanostructures for improved solar cell efficiency. Thin Solid Films 2014; 572: 126-33. https://doi.org/10.1016/j.tsf.2014.09.056
Kang BS, Ahn SE, Lee MJ, Stefanovich G, Kim KH, Xianyu WX, et al. High‐Current‐Density CuO x/InZnOx Thin‐Film Diodes for Cross‐Point Memory Applications. Adv Mater 2008; 20(16): 3066-9. https://doi.org/10.1002/adma.200702932
Zhang Q, Zhang K, Xu D, Yang G, Huang H, Nie F, et al. CuO nanostructures: synthesis, characterisation, growth mechanisms, fundamental properties, and applications. Prog Mater Sci 2014; 60: 208-337. https://doi.org/10.1016/j.pmatsci.2013.09.003
Baturay S, Candan I, Ozaydın C. Structural, optical, and electrical characterisations of Cr-doped CuO thin films. J Mater Sci Mater Electron 2022; 33(9): 7275-87. https://doi.org/10.1007/s10854-022-07918-2
Morales J, Sánchez L, Martín F, Ramos-Barrado JR, Sánchez M. Nanostructured CuO thin film electrodes prepared by spray pyrolysis: a simple method for enhancing the electrochemical performance of CuO in lithium cells. Electrochim Acta 2004; 49(26): 4589-97. https://doi.org/10.1016/j.electacta.2004.05.012
Menazea A, Mostafa AM. Ag-doped CuO thin film prepared via pulsed laser deposition for 4-nitrophenol degradation. J Environ Chem Eng 2020; 8(5): 104104. https://doi.org/10.1016/j.jece.2020.104104
Jundale D, Joshi P, Sen S, Patil V. Nanocrystalline CuO thin films: synthesis, microstructural and optoelectronic properties. J Mater Sci Mater Electron 2012; 23(8): 1492-9. https://doi.org/10.1007/s10854-011-0616-2
Dahrul M, Alatas H. Preparation and optical properties study of CuO thin film as applied solar cell on LAPAN-IPB Satellite. Procedia Environ Sci 2016; 33: 661-7. https://doi.org/10.1016/j.proenv.2016.03.121
Valladares LDLS, Salinas DH, Dominguez AB, Najarro DA, Khondaker S, Mitrelias T, et al. Crystallisation and electrical resistivity of Cu2O and CuO obtained by thermal oxidation of Cu thin films on SiO2/Si substrates. Thin Solid Films 2012; 520(20): 6368-74. https://doi.org/10.1016/j.tsf.2012.06.043
Al-Kuhaili M. Characterization of copper oxide thin films deposited by the thermal evaporation of cuprous oxide (Cu2O). Vacuum 2008; 82(6): 623-9. https://doi.org/10.1016/j.vacuum.2007.10.004
Terasako T, Ohmae K, Yamane M, Shirakata S. Carrier transport in undoped CdO films grown by atmospheric-pressure chemical vapor deposition. Thin Solid Films 2014; 572: 20-7. https://doi.org/10.1016/j.tsf.2014.07.061
Singh R, Yadav L, Shweta T. Effect of annealing time on the structural and optical properties of n-CuO thin films deposited by sol-gel spin coating technique and its application in n-CuO/p-Si heterojunction diode. Thin Solid Films 2019; 685: 195-203. https://doi.org/10.1016/j.tsf.2019.06.026
Masudy-Panah S, Radhakrishnan K, Tan HR, Yi R, Wong TI, Dalapati GK. Titanium-doped cupric oxide for photovoltaic application. Sol Energy Mater Sol Cells 2015; 140: 266-74. https://doi.org/10.1016/j.solmat.2015.04.024
Basith NM, Vijaya JJ, Kennedy LJ, Bououdina M. Structural, optical and room-temperature ferromagnetic properties of Fe-doped CuO nanostructures. Phys E: Low-Dimens Syst Nanostruct 2013; 53: 193-9. https://doi.org/10.1016/j.physe.2013.05.009
El Sayed A, Shaban M. Structural, optical and photocatalytic properties of Fe and (Co, Fe) co-doped copper oxide spin-coated films. Spectrochim. Acta A Mol 2015; 149: 638-46. https://doi.org/10.1016/j.saa.2015.05.010
Tawfik WZ, Khalifa ZS, Abdel-Wahab MS, Hammad AH. Sputtered cobalt-doped CuO nanostructured thin films for photoconductive sensors. J Mater Sci Mater Electron 2019; 30(2): 1275-81. https://doi.org/10.1007/s10854-018-0395-0
Dolai S, Dey R, Hussain S, Bhar R, Pal AK. Photovoltaic properties of F: SnO2/CdS/CuO/Ag heterojunction solar cell. Mater Res Bull 2019; 109: 1-9. https://doi.org/10.1016/j.materresbull.2018.09.022
Absike H, Essalhi Z, Labrim H, Hartiti B, Baaalla N, Tahiri M, et al. Synthesis of CuO thin films based on Taguchi design for solar absorber. Opt Mater 2021; 118: 111224. https://doi.org/10.1016/j.optmat.2021.111224
Piñón Reyes AC, Ambrosio Lázaro RC, Monfil Leyva K, Luna López JA, Flores Méndez J, Heredia Jiménez AH, et al. Study of a lead-free perovskite solar cell using CZTS as HTL to achieve a 20% PCE by SCAPS-1D simulation. Micromachines 2021; 12(12): 1508. https://doi.org/10.3390/mi12121508
AlZoubi T, Moghrabi A, Moustafa M, Yasin S. Efficiency boost of CZTS solar cells based on double-absorber architecture: Device modeling and analysis. Sol Energy 2021; 225: 44-52. https://doi.org/10.1016/j.solener.2021.07.012
Houimi A, Gezgin SY, Mercimek B, Kılıç HŞ. Numerical analysis of CZTS/n-Si solar cells using SCAPS-1D. A comparative study between experimental and calculated outputs. Opt Mater 2021; 121: 111544. https://doi.org/10.1016/j.optmat.2021.111544
Pallavolu MR, Reddy VRM, Pejjai B, Jeong D-s, Park C. Effect of sulfurisation temperature on the phase purity of Cu2SnS3 thin films deposited via high vacuum sulfurisation. Appl Surf Sci 2018; 462: 641-8. https://doi.org/10.1016/j.apsusc.2018.08.112
Das S, Alford T. Structural and optical properties of Ag-doped copper oxide thin films on polyethylene napthalate substrate prepared by low-temperature microwave annealing. J Appl Phys 2013; 113(24): 244905. https://doi.org/10.1063/1.4812584
Baturay Ş, Candan İ. Structural, Optical and Morphological Properties of Ag Doped CuO Thin Films Produced by Spin Coating Method. https://dergiparkorgtr/en/pub/yyufbed 2022. https://doi.org/10.21203/rs.3.rs-1118403/v1
Jabbar SM. Synthesis of CuO nanostructure via sol-gel and precipitation chemical methods. Al-Khawarizmi Eng J 2016; 12(4): 126-31. https://doi.org/10.22153/kej.2016.07.001
Mustafa FA. Optical properties of NaI doped polyvinyl alcohol films. Phys Sci Int J 2013; 1(1): 1-9. https://doi.org/10.1155/2013/897043
Antar E. Effect of γ-ray on optical characteristics of dyed PVA films. J Radiat Res Appl Sci 2014; 7(1): 129-34. https://doi.org/10.1016/j.jrras.2014.01.002
Gezgin SY. Modelling and investigation of the electrical properties of CIGS/n-Si heterojunction solar cells. Opt Mater 2022; 131: 112738. https://doi.org/10.1016/j.optmat.2022.112738
Jahan N, Kabir H, Taha H, Hossain MK, Rahman MM, Bashar M, et al. A holistic approach to optical characterisations of vacuum deposited Cu2ZnSnS4 thin film coatings for solar absorbing layers. J Alloys Compd 2021; 859: 157830. https://doi.org/10.1016/j.jallcom.2020.157830
Burgelman M, Decock K, Niemegeers A, Verschraegen J, Degrave S. SCAPS manual. February 2016.
Tripathi S, Lohia P, Dwivedi D. Contribution to sustainable and environmental friendly non-toxic CZTS solar cell with an innovative hybrid buffer layer. Sol Energy 2020; 204: 748-60. https://doi.org/10.1016/j.solener.2020.05.033
Jamil M, Amami M, Ali A, Mahmood K, Amin N. Numerical modeling of AZTS as buffer layer in CZTS solar cells with back surface field for the improvement of cell performance. Sol Energy 2022; 231: 41-6. https://doi.org/10.1016/j.solener.2021.11.025
Mishra SK, Padhy S, Singh UP. Silver incorporated bilayer Kesterite solar cell for enhanced device performance: A numerical study. Sol Energy 2022; 233: 1-10. https://doi.org/10.1016/j.solener.2022.01.021
Darvishzadeh P, Sohrabpoor H, Gorji NE. Numerical device simulation of carbon nanotube contacted CZTS solar cells. Opt Quantum Electron 2016; 48(10): 480. https://doi.org/10.1007/s11082-016-0741-5
Tousif MN, Mohammad S, Ferdous A, Hoque MA. Investigation of Different Materials as Buffer Layer in CZTS Solar Cells Using SCAPS. J Clean Energy Technol 2018; 6(4): 293-6. https://doi.org/10.18178/JOCET.2018.6.4.477
Frisk C, Ericson T, Li S-Y, Szaniawski P, Olsson J, Platzer-Björkman C. Combining strong interface recombination with bandgap narrowing and short diffusion length in Cu2ZnSnS4 device modeling. Sol Energy Mater Sol Cells 2016; 144: 364-70. https://doi.org/10.1016/j.solmat.2015.09.019
Haddout A, Fahoume M, Qachaou A, Raidou A, Lharch M, Elharfaoui N. Influence of composition ratio on the performances of kesterite solar cell with double CZTS layers—A numerical approach. Sol Energy 2019; 189: 491-502. https://doi.org/10.1016/j.solener.2019.07.098
Lam ND. Modelling and numerical analysis of ZnO/CuO/Cu2O heterojunction solar cell using SCAPS. Eng Res Express 2020; 2(2): 025033. https://doi.org/10.1088/2631-8695/ab9716
Adewoyin AD, Olopade MA, Oyebola OO, Chendo MA. Development of CZTGS/CZTS tandem thin film solar cell using SCAPS-1D. Optik 2019; 176: 132-42. https://doi.org/10.1016/j.ijleo.2018.09.033
AlZoubi T, Moustafa M. Numerical optimisation of absorber and CdS buffer layers in CIGS solar cells using SCAPS. Int J Smart Grid Clean Energy 2019; 8: 291-8. https://doi.org/10.12720/sgce.8.3.291-298
Hunter H. Simultaneous Ohmic Contacts to n and p-type Silicon Carbide for Future Electric Vehicles 2020.
Rahman MA. Performance analysis of WSe2-based bifacial solar cells with different electron transport and hole transport materials by SCAPS-1D. Heliyon 2022; 8(6): e09800. https://doi.org/10.1016/j.heliyon.2022.e09800
Niane D, Diagne O, Ehemba AK, Soce MM, Dieng M. Generation and Recombination of a CIGSe Solar Cell under the Influence of the Thickness of a Potassium Fluoride (KF) Layer. Am Mater Sci Eng 2018; 6(2): 26-30.
Abderrezek M, Djeghlal ME. Contribution to improve the performances of Cu2ZnSnS4 thin-film solar cells via a back surface field layer. Optik 2019; 181: 220-30. https://doi.org/10.1016/j.ijleo.2018.12.048
Djinkwi Wanda M, Ouédraogo S, Tchoffo F, Zougmoré F, Ndjaka J. Numerical investigations and analysis of Cu2ZnSnS4 based solar cells by SCAPS-1D. Int J Photoenergy 2016; 2016. https://doi.org/10.1155/2016/2152018
Abd El Halim B, Mahfoud A, Elamine DM. Numerical analysis of potential buffer layer for Cu2ZnSnS4 (CZTS) solar cells. Optik 2020; 204: 164155. https://doi.org/10.1016/j.ijleo.2019.164155
Meher S, Balakrishnan L, Alex Z. Analysis of Cu2ZnSnS4/CdS based photovoltaic cell: a numerical simulation approach. Superlattices Microstruct 2016; 100: 703-22. https://doi.org/10.1016/j.spmi.2016.10.028
Elhmaidi ZO, Pandiyan R, Abd-Lefdil M, El Khakani MA, editors. Pulsed laser deposition of CZTS thin films, their thermal annealing and integration into n-Si/CZTS photovoltaic devices 2016 International Renewable and Sustainable Energy Conference (IRSEC); 2016: IEEE. https://doi.org/10.1109/IRSEC.2016.7983988
Peksu E, Karaagac H. A third-generation solar cell based on wet-chemically etched Si nanowires and sol-gel derived Cu2ZnSnS4 thin films. J Alloys Compd 2019; 774: 1117-22. https://doi.org/10.1016/j.jallcom.2018.10.012
Gupta GK, Dixit A. Simulation studies of CZT (S, Se) single and tandem junction solar cells towards possibilities for higher efficiencies up to 22%. arXiv preprint arXiv: 180108498 2018.
Tchognia JHN, Hartiti B, Ndjaka J-M, Ridah A, Thevenin P. Performances des cellules solaires à base de Cu2ZnSnS4 (CZTS): Une analyse par simulations numériques via le simulateur SCAPS. Afr Sci 2015; 11(4): 16-23.
Padhy S, Mannu R, Singh UP. Graded band gap structure of kesterite material using bilayer of CZTS and CZTSe for enhanced performance: A numerical approach. Sol Energy 2021; 216: 601-9. https://doi.org/10.1016/j.solener.2021.01.057
Roy P, Tiwari S, Khare A. An investigation on the influence of temperature variation on the performance of tin (Sn) based perovskite solar cells using various transport layers and absorber layers. Results in Optics 2021; 4: 100083. https://doi.org/10.1016/j.rio.2021.100083
Abderrezek M, Fathi M, Djahli F. Comparative study of temperature effect on thin film solar cells 2018.
Zhang H, Cheng S, Yu J, Zhou H, Jia H. Prospects of Zn (O, S) as an alternative buffer layer for Cu2ZnSnS4 thin-film solar cells from numerical simulation. Micro Nano Lett 2016; 11(7): 386-90. https://doi.org/10.1049/mnl.2016.0130
Downloads
Published
How to Cite
Issue
Section
License
Policy for Journals/Articles with Open Access
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are permitted and encouraged to post links to their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work
Policy for Journals / Manuscript with Paid Access
Authors who publish with this journal agree to the following terms:
- Publisher retain copyright .
- Authors are permitted and encouraged to post links to their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work .