Microwaves Devulcanization of SBR Containing Carbon Black
DOI:
https://doi.org/10.6000/1929-5995.2016.05.02.1Keywords:
Devulcanization, microwaves, rubber recycling.Abstract
Polymer recycling has been the most suitable alternative for management of plastics waste that are responsible by serious environmental damages. However, the recycling of some polymer materials, such as vulcanized elastomers, is not a trivial process. The recycling of elastomers is a process more complex than the recycling of thermoplastic polymers because the elastomers cannot be remolded by simple heating after vulcanization. Methods for rubber devulcanization has been developed as an interesting alternative for recover flow properties of elastomers, allowing other molding cycle. The aim of this work was to evaluate the effect of the presence of carbon black on devulcanization of styrene-butadiene rubber (SBR) by microwaves and analyze properties of recycled material. The devulcanization by microwaves showed efficiency for rubber compositions with higher content of carbon black incorporated as well as the properties of recycled material showed satisfactory performance for reuse in other products. Microwaves devulcanization of SBR is an important alternative for reuse of rubber waste and decrease of the environmental problem generated with discard of these materials.
References
De D, Das A, Dey B. Debnath, SC, Roy BC. Reclaiming of ground rubber tire (GRT) by a novel reclaiming agent. Eur Polym J 2006; 42: 917-27. http://dx.doi.org/10.1016/j.eurpolymj.2005.10.003 DOI: https://doi.org/10.1016/j.eurpolymj.2005.10.003
Colom X, Canavate J, Carrilo F, Sunol JJ. Effect of the particle size and acid pretreatments on compatibility and properties of recycled HDPE plastic bottles filled with ground tyre powder. J Appl Polym Sci 2009; 15: 1882-90. http://dx.doi.org/10.1002/app.29611 DOI: https://doi.org/10.1002/app.29611
Mui ELK, Ko DCK, McKay G. Production of active carbons from waste tyres - a review. Carbon 2004; 42: 2789-805. http://dx.doi.org/10.1016/j.carbon.2004.06.023 DOI: https://doi.org/10.1016/j.carbon.2004.06.023
Garforth AA, Ali S, Hernandez-Martinez J, Akah A. Feedstock recycling of polymer wastes. Curr Opin Sol State Mater Sci 2004; 8: 419-25. http://dx.doi.org/10.1016/j.cossms.2005.04.003 DOI: https://doi.org/10.1016/j.cossms.2005.04.003
Adhikari B, De D, Maiti S. Reclamation and recycling of waste rubber. Prog Polym Sci 2000; 25: 909-48. http://dx.doi.org/10.1016/S0079-6700(00)00020-4 DOI: https://doi.org/10.1016/S0079-6700(00)00020-4
Rajan VV, Dierkes WK, Joseph R, Noordermeer JWN. Science and technology of rubber reclamation with special attention to NR-based waste latex products. Prog Polym Sci 2006; 31: 811-34. http://dx.doi.org/10.1016/j.progpolymsci.2006.08.003 DOI: https://doi.org/10.1016/j.progpolymsci.2006.08.003
Isayev AI, Sujan B. Nonisothermal vulcanization of devulcanized GRT with reversion type behavior. J Elastomers Plast 2006; 38: 291-318. http://dx.doi.org/10.1177/0095244306067424 DOI: https://doi.org/10.1177/0095244306067424
Wang X, Shi C, Zhang L, Zhang Y. Effects of shear stress and subcritical water on devulcanization of styrene–butadiene rubber based ground tire rubber in a twin-screw extruder. J Appl Polym Sci 2013; 130: 1845-54. http://dx.doi.org/10.1002/app.39253 DOI: https://doi.org/10.1002/app.39253
Paulo GD, Hirayama D, Saron C. Microwave devulcanization of waste rubber with inorganic salts and nitric acid. Adv Mater Res 2012; 418-420: 1072-5. http://dx.doi.org/10.4028/www.scientific.net/AMR.418-420.1072 DOI: https://doi.org/10.4028/www.scientific.net/AMR.418-420.1072
Hirayama D, Saron C. Chemical modifications in styrene–butadiene rubber after microwave devulcanization. Ind Eng Chem Res 2012; 51: 3975-80. http://dx.doi.org/10.1021/ie202077g DOI: https://doi.org/10.1021/ie202077g
Jiang G, Zhao S, Li W, et al. Microbial desulfurization of SBR ground rubber by Sphingomonas sp. and its utilization as filler in NR compounds. Polym Adv Technol 2011; 22: 2344-51. http://dx.doi.org/10.1002/pat.1769 DOI: https://doi.org/10.1002/pat.1769
Lidstrom P, Tierney J, Wathey B, Westman J. Microwave-assisted organic synthesis: a review. Tetrahedron 2001; 57: 9225-83. http://dx.doi.org/10.1016/S0040-4020(01)00906-1 DOI: https://doi.org/10.1016/S0040-4020(01)00906-1
Siores E, Dorego DJ. Microwave applications in materials joining. Mater Process Technol 1995; 48: 619-25. http://dx.doi.org/10.1016/0924-0136(94)01701-2 DOI: https://doi.org/10.1016/0924-0136(94)01701-2
Thostenson ET, Chou TW. Microwave processing: fundamentals and applications. Composites A-Appl Sci Manuf 1999; 30: 1055-71. http://dx.doi.org/10.1016/S1359-835X(99)00020-2 DOI: https://doi.org/10.1016/S1359-835X(99)00020-2
Al-Harahsheh M, Kingman SW. Microwave-assisted leaching—a review. Hydrometallurgy 2004; 73: 189-203. http://dx.doi.org/10.1016/j.hydromet.2003.10.006 DOI: https://doi.org/10.1016/j.hydromet.2003.10.006
Jones DA, Lelyveld TP, Mavrofidis SD, Kingman SW, Miles N. Microwave heating applications in environmental engineering—a review. J Resourc Conserv Recycling 2002; 34: 75-90. http://dx.doi.org/10.1016/S0921-3449(01)00088-X DOI: https://doi.org/10.1016/S0921-3449(01)00088-X
Landini L, Araujo SG, Lugao AB, Wiebeck H. Preliminary analysis to BIIR recovery using the microwave process. Eur Polym J 2007; 43: 2725-31. http://dx.doi.org/10.1016/j.eurpolymj.2007.03.017 DOI: https://doi.org/10.1016/j.eurpolymj.2007.03.017
Scuracchio CH, Waki DA, Silva MLC. Thermal analysis of ground tire rubber devulcanized by microwaves. J Thermal Anal Calorim 2007; 87: 893-7. http://dx.doi.org/10.1007/s10973-005-7419-8 DOI: https://doi.org/10.1007/s10973-005-7419-8
Kleps T, Piaskiewicz M, Parasiewicz W. The use of thermogravimetry in the study of rubber devulcanization. J Thermal Anal Calorim 2000; 60: 271-7. http://dx.doi.org/10.1023/A:1010134315762 DOI: https://doi.org/10.1023/A:1010134315762
Garcia PS, Souza FDB, Cruz SA, Scuracchio CH. Devulcanization of ground tire rubber: Physical and chemical changes after different microwave exposure times. Express Polym Lett 2015; 9: 1015-26. http://dx.doi.org/10.3144/expresspolymlett.2015.91 DOI: https://doi.org/10.3144/expresspolymlett.2015.91
Molanorouzi M, Mohaved SO. Reclaiming waste tire rubber by an irradiation technique. Polym Degrad Stab 2016; 128: 115-25. http://dx.doi.org/10.1016/j.polymdegradstab.2016.03.009 DOI: https://doi.org/10.1016/j.polymdegradstab.2016.03.009
Colom X, Faliq A, Formela K, Canavate J. FTIR spectroscopic and thermogravimetric characterization of ground tyre rubber devulcanized by microwave treatment. Polym Testing 2016; 52: 200-8. http://dx.doi.org/10.1016/j.polymertesting.2016.04.020 DOI: https://doi.org/10.1016/j.polymertesting.2016.04.020
Liu J, Liu P, Zhang X, Lu P, Zhang X, Zhang M. Fabrication of magnetic rubber composites by recycling waste rubber powders via a microwave-assisted in situ surface modification and semi-devulcanization process. Chem Eng J 2016; 295: 73-9. http://dx.doi.org/10.1016/j.cej.2016.03.025 DOI: https://doi.org/10.1016/j.cej.2016.03.025
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2016 Journal of Research Updates in Polymer Science
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Policy for Journals/Articles with Open Access
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are permitted and encouraged to post links to their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work
Policy for Journals / Manuscript with Paid Access
Authors who publish with this journal agree to the following terms:
- Publisher retain copyright .
- Authors are permitted and encouraged to post links to their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work .