Tribology Behavior of In-Situ FDM 3D Printed Glass Fibre-Reinforced Thermoplastic Composites
DOI:
https://doi.org/10.6000/1929-5995.2024.13.10Keywords:
Additive manufacturing, Fused deposition modeling, Extrusion, Polymer compositesAbstract
Fused deposition modeling (FDM) 3D-printed parts are generally weaker compared to injection-moulded parts. Fibre reinforcement is one of the techniques used to enhance the mechanical strength and the tribological behavior of the FDM-printed parts. Recently, a new method for creating FDM 3D-printed composites was developed. Current work focuses on the tribological behavior of the glass fibre-reinforced PLA, manufactured using this new composite manufacturing method. Experiments were conducted to investigate the effect of Glass Fibre (GF) reinforcement on FDM 3D-printed thermoplastic composites, specifically polylactic acid (PLA) under different linear sliding speed and directions. All 3D printed glass fibre-reinforced PLA (PLA-GF) composites exhibited a lower wear rate and a higher friction coefficient compared to 3D printed PLA. Increasing in disc’s linear speed or sliding speed of the pins resulted in a lower coefficient of friction and wear rate. In addition, a perpendicular raster direction towards the disc rotation or pin motion experienced greater friction and greater wear.
References
Reddy KS, Dufera S. Additive Manufacturing Technologies. Int J Manag Inf Technol Eng 2016; 4(7): 89-112. https://doi.org/10.1016/j.bushor.2017.05.011
Attaran M. The rise of 3-D printing: The advantages of additive manufacturing over traditional manufacturing. Bus Horiz 2017; 60(5): 677-688. DOI: https://doi.org/10.1016/j.bushor.2017.05.011
Bates-Green K, Howie T. Materials for 3D printing by fused deposition. Tech Educ Addit Manuf Mater 2016; 1-21.
Beniak J, Križan P, Matúš M, Šajgalík M. Experimental testing of PLA biodegradable thermoplastic in the frame of 3D printing FDM technology. MATEC Web Conf 2018; 157: 0-6. https://doi.org/10.1051/matecconf/201815706001 DOI: https://doi.org/10.1051/matecconf/201815706001
Ismail KI, Yap TC, Ahmed R. 3D-Printed Fiber-Reinforced Polymer Composites by Fused Deposition Modelling (FDM): Fiber Length and Fiber Implementation Techniques. Polymers (Basel) 2022; 14(21). https://doi.org/10.3390/polym14214659 DOI: https://doi.org/10.3390/polym14214659
Prabhakar K, Debnath S, Ganesan R, Palanikumar K. A review of mechanical and tribological behaviour of polymer composite materials. IOP Conf Ser Mater Sci Eng 2018; 344: 012015. https://doi.org/10.1088/1757-899X/344/1/012015 DOI: https://doi.org/10.1088/1757-899X/344/1/012015
Sivaraos, et al. Friction Performance Analysis of Waste Tire Rubber Powder Reinforced Polypropylene Using Pin-On-Disk Tribometer. Procedia Eng 2013; 68(0): 743-749. https://doi.org/10.1016/j.proeng.2013.12.248 DOI: https://doi.org/10.1016/j.proeng.2013.12.248
McMullen P. Fibre/resin composites for aircraft primary structures: a short history, 1936-1984. Composites 1984; 15(3): 222-230. https://doi.org/10.1016/0010-4361(84)90279-9 DOI: https://doi.org/10.1016/0010-4361(84)90279-9
Such M, Ward C, Potter K. Aligned Discontinuous Fibre Composites: A Short History. J Multifunct Compos 2014; 2(3): 155-168. https://doi.org/10.12783/issn.2168-4286/2/3/4/Such DOI: https://doi.org/10.12783/issn.2168-4286/2/3/4/Such
Cheloni JPM, Silveira ME, Lopes, da Silva LJ. Fatigue and Failure Analysis of Sandwich Composites using Two Types of Cross-Ply Glass Fibers Laminates and Epoxy Resin. J Res Updat Polym Sci 2022; 11: 36-44. https://doi.org/10.6000/1929-5995.2022.11.06 DOI: https://doi.org/10.6000/1929-5995.2022.11.06
Das D, Dubey OP, Sharma OP, Nayak RK, Samal C. Mechanical properties and abrasion behaviour of glass fiber reinforced polymer composites - A case study. Mater Today Proc 2019; 19: 506-511. https://doi.org/10.1016/j.matpr.2019.07.644 DOI: https://doi.org/10.1016/j.matpr.2019.07.644
Mohammadizadeh M, Imeri A, Fidan I, Elkelany M. 3D printed fiber reinforced polymer composites - Structural analysis. Compos Part B Eng 2019; 175: 107112. https://doi.org/10.1016/j.compositesb.2019.107112 DOI: https://doi.org/10.1016/j.compositesb.2019.107112
Ismail KI, Pang R, Ahmed R, Yap TC. Tensile Properties of In Situ 3D Printed Glass Fiber-Reinforced PLA. Polymer 2023; 15(16): 3436. https://doi.org/10.3390/polym15163436 DOI: https://doi.org/10.3390/polym15163436
Rouf S, Raina A, Irfan Ul Haq M, Naveed N, Jeganmohan S, Farzana Kichloo A. 3D printed parts and mechanical properties: Influencing parameters, sustainability aspects, global market scenario, challenges and applications. Adv Ind. Eng Polym Res 2022; 5(3): 143-158. https://doi.org/10.1016/j.aiepr.2022.02.001 DOI: https://doi.org/10.1016/j.aiepr.2022.02.001
Ismail KI, Ramarad S, Yap TC. Design and Fabrication of an In Situ Short-Fiber Doser for Fused Filament Fabrication 3D Printer: A Novel Method to Manufacture Fiber-Polymer Composite. Inventions 2023; 8(1): 2023. https://doi.org/10.3390/inventions8010010 DOI: https://doi.org/10.3390/inventions8010010
Maguluri N, Lakshmi Srinivas C, Suresh G. Assessing the wear performance of 3D printed polylactic acid polymer parts. Mater. Today Proc 2023. https://doi.org/10.1016/j.matpr.2023.04.565 DOI: https://doi.org/10.1016/j.matpr.2023.04.565
Chithambaram K, Senthilnathan N. Effects of printing parameters on hardness and wear characteristics of 3D printed polyetheretherketone (PEEK) polymer. Mater Lett 2024; 356: 135588. https://doi.org/10.1016/j.matlet.2023.135588 DOI: https://doi.org/10.1016/j.matlet.2023.135588
Dangnan F, Espejo C, Liskiewicz T, Gester M, Neville A. Friction and wear of additive manufactured polymers in dry contact. J Manuf Process 2020; 59: 238-247. https://doi.org/10.1016/j.jmapro.2020.09.051 DOI: https://doi.org/10.1016/j.jmapro.2020.09.051
Zainal M, Ismail K, Yap T. Tribological Properties of PLA 3D Printed at Different Extrusion Temperature. J Phys Conf Ser 2023; 2542(1): 012001. https://doi.org/10.1088/1742-6596/2542/1/012001 DOI: https://doi.org/10.1088/1742-6596/2542/1/012001
Palaniandy L, Ismail KI, Yap TC, “Tribological Behaviour of 3D printed Polylactic Acid (PLA) Sliding Against Steel at Different Sliding Speed. J Phys Conf Ser 2023; 2542(1): 012003. https://doi.org/10.1088/1742-6596/2542/1/012003 DOI: https://doi.org/10.1088/1742-6596/2542/1/012003
Bardi MAEA, Bokade SA, Gunjal SL, Bedade OR, Manohar SS. Review of Enhancement of Polymer for Material Extrusion Process by Combining with Filler Material. in Lecture Notes in Mechanical Engineering 2022; 869-883. https://doi.org/10.1007/978-981-16-7787-8_69 DOI: https://doi.org/10.1007/978-981-16-7787-8_69
Archard JF. Contact and Rubbing of Flat Surfaces. J Appl Phys 1953; 24(8): 981-988. https://doi.org/10.1063/1.1721448 DOI: https://doi.org/10.1063/1.1721448
Greenwood JA. Surface Temperatures in Sliding. Encycl Therm Stress 2014; 4749-4758. https://doi.org/10.1007/978-94-007-2739-7_688 DOI: https://doi.org/10.1007/978-94-007-2739-7_688
Lates MT. Friction induced heating properties of the polyamide/steel type contacts. IOP Conf Ser Mater Sci Eng 2020; 898(1): 012004. https://doi.org/10.1088/1757-899X/898/1/012004 DOI: https://doi.org/10.1088/1757-899X/898/1/012004
Bahadur S. The development of transfer layers and their role in polymer tribology. Wear 2000; 245(1-2): 92-99 https://doi.org/10.1016/S0043-1648(00)00469-5 DOI: https://doi.org/10.1016/S0043-1648(00)00469-5
Aworinde AK, Emagbetere E, Adeosun SO, Akinlabi ET. Polylactide and its composites on various scales of hardness. Pertanika J Sci Technol 2021; 29(2): 1313-1322. https://doi.org/10.47836/pjst.29.2/34 DOI: https://doi.org/10.47836/pjst.29.2.34
Prasad L, Kapri P, Patel RV, Yadav A, Winczek J. Physical and Mechanical Behavior of Ramie and Glass Fiber Reinforced Epoxy Resin-Based Hybrid Composites. J Nat Fibers 2023; 20(2). https://doi.org/10.1080/15440478.2023.2234080 DOI: https://doi.org/10.1080/15440478.2023.2234080
Downloads
Published
How to Cite
Issue
Section
License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Policy for Journals/Articles with Open Access
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are permitted and encouraged to post links to their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work
Policy for Journals / Manuscript with Paid Access
Authors who publish with this journal agree to the following terms:
- Publisher retain copyright .
- Authors are permitted and encouraged to post links to their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work .